Monstera Adansonii is a rapidly growing vining plant found throughout South and Central America. This plant can climb walls and grow as vines from dangling baskets.
Monstera Adansonii is breathtaking, yet there is never enough of it. You may even attempt propagating it and growing a new plant to give as a gift to your pals. In this article, we will discuss how to propagate Monstera Adansonii.
Monsteras are Swiss cheese vines or plants because of their lacy notches and holes in the leaves, and adansonii is the cheesiest among them all.
The leaves are more fragile and perforated than those of deliciosa. Although all Monsteras are vines, monstera adansonii particularly has a trailing aspect that makes it ideal for hanging baskets.
Learning how to propagate Monstera Adansonii will allow you to add these beautiful houseplants to your collection and even gift them to a friend.
Things you Will Need.
- An incredibly sharp and disinfected knife/blade
- A glass jar having rainwater or filtered water.
- A small pot having fresh soil
A Guide on How to Propagate Monstera Adansonii
Monstera adansonii propagation is simple, as with many vining plants. Monstera Adansonii can be grown in water, perlite, sphagnum moss, or in the soil directly. You can even leave it in water indefinitely, though it will not develop as well as it would in soil.
Step 1: Locate a mature and healthy vine section.
- Locate a mature portion of the vine to take a Monstera adansonii cutting, one with a stem that is at least as thick as a drinking straw.
- Cutting an immature vine portion will result in a low success rate since the plant tissue will be damaged.
- Look for a plant part with a few leaves and a little brown node beneath the leaves to meet the stem.
- Monstera nodes are thin brown rings on the main stem showing an old leaf formerly wrapped around it.
- An aerial root may already be sprouting from the plant stem.
Step 2: Take a cutting from a mature Monstera Adansonii vine
- Cut a bit below a node with a sterilized knife or clippers. As a result of the plant being harmed, stem cells localized around the node will be stimulated to rebuild tissue. These are the cells that will cause a new root system to emerge.
- It only takes an inch or two of cutting to make a noticeable difference.
- The quantity and size of leaves on the cutting should be kept to a minimum to allow the new plant to concentrate its energy on root development rather than supporting foliage that has little or no potential to absorb water.
Step 3: Propagation
Propagation in Water
Water propagation is a fantastic option for less-skilled (or curious) gardeners since it allows you to see the root system grow and develop in real-time. It’s also a rather quick way to propagate.
- Fill a glass jar halfway with filtered water or rainwater.
- Insert your cuttings with the cut side downwards in the water to plant. That’s all there is to it!
- Of course, putting a rooting hormone solution in the water will help, but it isn’t required.
- You can put one clipping or a few into a single jar as you begin propagation.
- When growing, be aware that the roots will intertwine; when separating plants, you run the risk of harming them.
- Place the jar in an area that receives a reasonable quantity of sunshine, with the cut end of your cutting submerged in water.
- You want your cutting to get lots of suns, but not in direct sunshine or at high temperatures.
- You must now wait for the snip to sprout roots!
- If the water level in your jar starts to fall, fill it with room-temperature distilled water.
- To prevent fungi or debris from growing and hindering your plant’s growth, change the water in your jar entirely every two to three days.
- If you see a murky color or pieces of debris floating in your water, replace it immediately!
- Although you can leave your clipping to develop in water, if you decide to transplant it to the soil once it has begun to grow, wait until the roots have grown to at least an inch in length.
- Within a month or two, you should find that your clipping has reached this standard.
- Pour a little fresh potting mix in the base of a clean, well-drained pot to pot up your water-grown Monstera cutting.
- Place the snip in the center of the soil and fill it around it with extra soil until the roots are completely covered.
- Soak the potting soil thoroughly from the bottom up until your plant roots are completely coated in the soil.
- Place the pot in a pool of water, and the earth will absorb the water through the drainage holes.
- Place the potted cutting in a location that receives a modest quantity of indirect sunlight.
- Wait until the soil has completely dried before watering your clipping again.
Propagation in Soil
- To plant your cutting in soil, start with a clean plant container with adequate drainage and fill it halfway with potting soil.
- Then, in the center of the plant pot, place your clipping and pour additional potting mix till the node on your clipping is buried beneath the soil.
- Saturate the soil with filtered water at room temperature after it has been covered with soil, then place your planted clipping somewhere where it will receive moderate indirect sunlight.
- If you lay your clipping in direct sunlight, it will suffer the same fate as any mature plant, and you won’t see any growth.
- Root growth should begin within the first month of potting your clipping, but to be cautious, wait two months before presuming the clipping has taken root.
- Write the planting date on a label or a calendar to keep track.
- Keep the soil moist while the roots of your Monstera clipping grow.
- As the vine is native to the tropics of South and Central America, it can withstand a little more moisture than most houseplants.
- It would be best if you watered it once a week to once every two weeks, depending on the amount of sunlight it receives.
It has only a few basic requirements for care:
- Indirect, bright light
- Don’t let it dry completely—wet it once the topmost inch is dry.
- Plant in a potting mix that drains properly.
- Warmth and humidity are provided.
- During the growing season, use a suitable houseplant fertilizer once a month.
- After one to two years, repot.
- Please give it a moss pole to hang on.
It’s ideal for a newbie looking for a one-of-a-kind houseplant! Now that you know how to propagate Monstera Adansonii, you can easily grow them at home.
These plants are easy to grow and equally easy to care for. It is critical to take care of both the mother plant and cuttings when propagating your plants.
This includes not only thinking about feeding, watering, and light exposure but also being cautious not to over-strip your mother plant in an attempt to produce too many cuttings.
Take just a few clippings at a time to keep the mother Monstera Adansonii plant healthy. A good rule of thumb is to remove no more than 25% of the plant’s mass at a time. After you’ve collected your cuttings, give the mother plant some time to heal before you start propagating again.